Patcat 3001 – Dibutyltin diluarate is a clear, yellowish liquid.
Patcat 3001 is a primary catalyst to accelerate the isocyanate-hydroxyl-reaction as well as the reaction of isocyanates with alcohols. It can be combined with tertiary amiens and calcium-2-ethyl-hexanoate. It can also be used for silanol condensation reaction.
Patcat 3001 is used in the range of 0.1-0.5% referring to polyol as primary catalyst for most PUR – formulations and as a secondary catalyst 0.03 – 0.3% recommended. For silicone systems 0.1-1% required for hardening.
It is recommended that the appropriate addition level of Patcat 3001 is determined experimentally.
Patcat 3003 - Dibutyltin diacetate. Liquid catalyst for polyurethane and silicone systems and for esterification reactions. Higher activity and rates than DBTL.
Patcat 3003 is an active catalyst for transesterification and urethane cross-linking reaction. It is also used for silanol condensation and esterfication.
Patcat 3003 is applicable for Polyurethane foams, Polyurethane coatings (coil coatings, high-solids), Polyurethane adhesives, Alkyd resins, Silicone resins, Polyester resins, Fatty acid esters, Acrylic and methycrylic esters, Lubricant ester and RTV Silicones sealants (acetoxy, oxime curing; 2 k systems).
It is recommended that the appropriate addition level of DBTA is determined experimentally.
Patcat 3004 – Dibutyltin neodecanoate is a clear, yellowish liquid.
Patcat 3004 is a primary catalyst to accelerate the isocyanate-hydroxyl-reaction as well as the reaction of isocyanates with alcohols. It can also be used for esterification of fatty acids.
Patcat 3004 is widely applicable for polyurethanes, MS-polymers, RTV Silicones and Fatty acid esters.
It is recommended that the appropriate addition level of Patcat 3004 is determined experimentally.
Patcat 3005 is Dioctyltin dilaurate, which does not impart odour to the polymers being produced.
Patcat 3005 solidifies if stored below 17o C. If solidification occurs, simply warm to a temperature of max. 40oC and mix homogeneously, there is no loss of performance as catalyst.
Patcat 3005 should preferably be stored in tightly closed original containers, protected from humidity and at room temperature.
Patcat 3005 is supplied in standard steel drums which satisfy UN regulations.
It is recommended that the appropriate addition level of Patcat 3005 is determined experimentally.
Patcat 3008 is Dioctyltin bis(2-ethylhexanoate) waxy yellowish substance.
Patcat 3008 solidifies if stored below 25oC. If solidification occurs, simply warm to a temperature of max. 40oC and mix homogeneously, there is no loss of performance as catalyst will be occurred.
Patcat 3008 should preferably be stored in tightly closed original containers, protected from humidity and at room temperature.
Patcat 3008 is supplied in standard steel drums which satisfy UN regulations.
Patcat 3009 is Dioctyltin Carboxylate, belonging to the group of dioctyltiin laureates. It is preffered when less odour with light coloured product required.
Patcat 3009 should preferably be stored in containers, protected from humidity and at room temperature.
Patcat 3009 solidifies if stored below 6oc, depends on the storage time. If solidification occurs, simply warm the material up to room temperature and mix homogeneously, there is no loss of performance as catalyst.
Patcat 3009 is supplied in standard packing which satisfy UN regulations.
Patcat 3010 Dibutyltin bis(2,ethylhexanoate) in 2-ethylhexanoic acid
Patcat 3010 – Dibutyltin bis (2-Ethylhexanoate) in 2-Ethylhexanoic Acid is a clear liquid.
Patcat 3010 is applicable for the Silanol condensation polymerization reaction and Silicone Elastomers. It is also applicable for one or two component systems that are compatible with aromatic solvents.
It is recommended that the appropriate addition level of Patcat 3010 is determined experimentally.
Patcat 3012 is Stannous Octoate, a catalyst for the production of Poly Urethane foams.
Application:
Patcat 3012 is an important catalyst for the production of Polyether polyurethane foams. It accelerates mainly the gelling reaction. The simultaneous application of a tertiary amine activator interacts with Patcat 3012 to influence the blowing effect.
Patcat 3014 - Dibutyltin bis(laurylmercaptide) is clear colourless liquid.
Patcat 3014 is used as catalyst to accelerate the isocynate – hydroxyl reaction. It is recommended in the manufacturing of Polyurethanes, HR Foams.
It is recommended that the appropriate addition level of Patcat 3014 is determined experimentally.
Patcat 3014 is supplied in standard steel drums which satisfy UN regulations.
To be kept dry. Containers should be tightly resealed after use.
Patcat 3015 is Dibutyltin Carboxylate, belonging to the group of dibutyltin laureates It is preferred when less odour with light coloured product required.
Patcat 3015 should preferably be stored in containers, protected from humidity and at room temperature.
Patcat 3015 is supplied in standard packing which satisfy UN regulations.
Patcat 3001 – Dibutyltin diluarate is a clear, yellowish liquid.
Patcat 3001 is a primary catalyst to accelerate the isocyanate-hydroxyl-reaction as well as the reaction of isocyanates with alcohols. It can be combined with tertiary amiens and calcium-2-ethyl-hexanoate. It can also be used for silanol condensation reaction.
Patcat 3001 is used in the range of 0.1-0.5% referring to polyol as primary catalyst for most PUR – formulations and as a secondary catalyst 0.03 – 0.3% recommended. For silicone systems 0.1-1% required for hardening.
It is recommended that the appropriate addition level of Patcat 3001 is determined experimentally.
Patcat 3003 - Dibutyltin diacetate. Liquid catalyst for polyurethane and silicone systems and for esterification reactions. Higher activity and rates than DBTL.
Patcat 3003 is an active catalyst for transesterification and urethane cross-linking reaction. It is also used for silanol condensation and esterfication.
Patcat 3003 is applicable for Polyurethane foams, Polyurethane coatings (coil coatings, high-solids), Polyurethane adhesives, Alkyd resins, Silicone resins, Polyester resins, Fatty acid esters, Acrylic and methycrylic esters, Lubricant ester and RTV Silicones sealants (acetoxy, oxime curing; 2 k systems).
It is recommended that the appropriate addition level of DBTA is determined experimentally.
Patcat 3004 – Dibutyltin neodecanoate is a clear, yellowish liquid.
Patcat 3004 is a primary catalyst to accelerate the isocyanate-hydroxyl-reaction as well as the reaction of isocyanates with alcohols. It can also be used for esterification of fatty acids.
Patcat 3004 is widely applicable for polyurethanes, MS-polymers, RTV Silicones and Fatty acid esters.
It is recommended that the appropriate addition level of Patcat 3004 is determined experimentally.
Patcat 3005 is Dioctyltin dilaurate, which does not impart odour to the polymers being produced.
Patcat 3005 solidifies if stored below 17o C. If solidification occurs, simply warm to a temperature of max. 40oC and mix homogeneously, there is no loss of performance as catalyst.
Patcat 3005 should preferably be stored in tightly closed original containers, protected from humidity and at room temperature.
Patcat 3005 is supplied in standard steel drums which satisfy UN regulations.
It is recommended that the appropriate addition level of Patcat 3005 is determined experimentally.
Patcat 3008 is Dioctyltin bis(2-ethylhexanoate) waxy yellowish substance.
Patcat 3008 solidifies if stored below 25oC. If solidification occurs, simply warm to a temperature of max. 40oC and mix homogeneously, there is no loss of performance as catalyst will be occurred.
Patcat 3008 should preferably be stored in tightly closed original containers, protected from humidity and at room temperature.
Patcat 3008 is supplied in standard steel drums which satisfy UN regulations.
Patcat 3009 is Dioctyltin Carboxylate, belonging to the group of dioctyltiin laureates. It is preffered when less odour with light coloured product required.
Patcat 3009 should preferably be stored in containers, protected from humidity and at room temperature.
Patcat 3009 solidifies if stored below 6oc, depends on the storage time. If solidification occurs, simply warm the material up to room temperature and mix homogeneously, there is no loss of performance as catalyst.
Patcat 3009 is supplied in standard packing which satisfy UN regulations.
Patcat 3010 Dibutyltin bis(2,ethylhexanoate) in 2-ethylhexanoic acid
Patcat 3010 – Dibutyltin bis (2-Ethylhexanoate) in 2-Ethylhexanoic Acid is a clear liquid.
Patcat 3010 is applicable for the Silanol condensation polymerization reaction and Silicone Elastomers. It is also applicable for one or two component systems that are compatible with aromatic solvents.
It is recommended that the appropriate addition level of Patcat 3010 is determined experimentally.
Patcat 3012 is Stannous Octoate, a catalyst for the production of Poly Urethane foams.
Application:
Patcat 3012 is an important catalyst for the production of Polyether polyurethane foams. It accelerates mainly the gelling reaction. The simultaneous application of a tertiary amine activator interacts with Patcat 3012 to influence the blowing effect.
Patcat 3014 - Dibutyltin bis(laurylmercaptide) is clear colourless liquid. Patcat 3014 is used as catalyst to accelerate the isocynate – hydroxyl reaction. It is recommended in the manufacturing of Polyurethanes, HR Foams.
It is recommended that the appropriate addition level of Patcat 3014 is determined experimentally.
Patcat 3014 is supplied in standard steel drums which satisfy UN regulations.
To be kept dry. Containers should be tightly resealed after use.
Patcat 3015 is Dibutyltin Carboxylate, belonging to the group of dibutyltin laureates It is preferred when less odour with light coloured product required.
Patcat 3015 should preferably be stored in containers, protected from humidity and at room temperature.
Patcat 3015 is supplied in standard packing which satisfy UN regulations.
Patcat 3001 – Dibutyltin diluarate is a clear, yellowish liquid.
Patcat 3001 is a primary catalyst to accelerate the isocyanate-hydroxyl-reaction as well as the reaction of isocyanates with alcohols. It can be combined with tertiary amiens and calcium-2-ethyl-hexanoate. It can also be used for silanol condensation reaction.
Patcat 3001 is used in the range of 0.1-0.5% referring to polyol as primary catalyst for most PUR – formulations and as a secondary catalyst 0.03 – 0.3% recommended. For silicone systems 0.1-1% required for hardening.
It is recommended that the appropriate addition level of Patcat 3001 is determined experimentally.
Patcat 3003 - Dibutyltin diacetate. Liquid catalyst for polyurethane and silicone systems and for esterification reactions. Higher activity and rates than DBTL.
Patcat 3003 is an active catalyst for transesterification and urethane cross-linking reaction. It is also used for silanol condensation and esterfication.
Patcat 3003 is applicable for Polyurethane foams, Polyurethane coatings (coil coatings, high-solids), Polyurethane adhesives, Alkyd resins, Silicone resins, Polyester resins, Fatty acid esters, Acrylic and methycrylic esters, Lubricant ester and RTV Silicones sealants (acetoxy, oxime curing; 2 k systems).
It is recommended that the appropriate addition level of DBTA is determined experimentally.
Patcat 3004 – Dibutyltin neodecanoate is a clear, yellowish liquid.
Patcat 3004 is a primary catalyst to accelerate the isocyanate-hydroxyl-reaction as well as the reaction of isocyanates with alcohols. It can also be used for esterification of fatty acids.
Patcat 3004 is widely applicable for polyurethanes, MS-polymers, RTV Silicones and Fatty acid esters.
It is recommended that the appropriate addition level of Patcat 3004 is determined experimentally.
Patcat 3005 is Dioctyltin dilaurate, which does not impart odour to the polymers being produced.
Patcat 3005 solidifies if stored below 17o C. If solidification occurs, simply warm to a temperature of max. 40oC and mix homogeneously, there is no loss of performance as catalyst.
Patcat 3005 should preferably be stored in tightly closed original containers, protected from humidity and at room temperature.
Patcat 3005 is supplied in standard steel drums which satisfy UN regulations.
It is recommended that the appropriate addition level of Patcat 3005 is determined experimentally.
Patcat 3008 is Dioctyltin bis(2-ethylhexanoate) waxy yellowish substance.
Patcat 3008 solidifies if stored below 25oC. If solidification occurs, simply warm to a temperature of max. 40oC and mix homogeneously, there is no loss of performance as catalyst will be occurred.
Patcat 3008 should preferably be stored in tightly closed original containers, protected from humidity and at room temperature.
Patcat 3008 is supplied in standard steel drums which satisfy UN regulations.
Patcat 3009 is Dioctyltin Carboxylate, belonging to the group of dioctyltiin laureates. It is preffered when less odour with light coloured product required.
Patcat 3009 should preferably be stored in containers, protected from humidity and at room temperature.
Patcat 3009 solidifies if stored below 6oc, depends on the storage time. If solidification occurs, simply warm the material up to room temperature and mix homogeneously, there is no loss of performance as catalyst.
Patcat 3009 is supplied in standard packing which satisfy UN regulations.
Patcat 3010 Dibutyltin bis(2,ethylhexanoate) in 2-ethylhexanoic acid
Patcat 3010 – Dibutyltin bis (2-Ethylhexanoate) in 2-Ethylhexanoic Acid is a clear liquid.
Patcat 3010 is applicable for the Silanol condensation polymerization reaction and Silicone Elastomers. It is also applicable for one or two component systems that are compatible with aromatic solvents.
It is recommended that the appropriate addition level of Patcat 3010 is determined experimentally.
Patcat 3012 is Stannous Octoate, a catalyst for the production of Poly Urethane foams.
Application:
Patcat 3012 is an important catalyst for the production of Polyether polyurethane foams. It accelerates mainly the gelling reaction. The simultaneous application of a tertiary amine activator interacts with Patcat 3012 to influence the blowing effect.
Patcat 3014 - Dibutyltin bis(laurylmercaptide) is clear colourless liquid. Patcat 3014 is used as catalyst to accelerate the isocynate – hydroxyl reaction. It is recommended in the manufacturing of Polyurethanes, HR Foams.
It is recommended that the appropriate addition level of Patcat 3014 is determined experimentally.
Patcat 3014 is supplied in standard steel drums which satisfy UN regulations.
To be kept dry. Containers should be tightly resealed after use.
Patcat 3015 is Dibutyltin Carboxylate, belonging to the group of dibutyltin laureates It is preferred when less odour with light coloured product required.
Patcat 3015 should preferably be stored in containers, protected from humidity and at room temperature.
Patcat 3015 is supplied in standard packing which satisfy UN regulations.
Polyurethane Coating 
